本文聚焦 2026 年 10 月下旬以来两份可核验的公开材料:四川省 10 月 27 日公开印发的重点行业节能降碳改造攻坚三年行动方案,以及中国有色金属工业协会 10 月 30 日召开的前三季度运行情况新闻发布会问答录,并把它们放回国家层面三年攻坚行动的框架里理解。政策文本、行业运行数据与省级目标分属不同发布方和统计口径,文中逐处标注,不作混用。
一、三年攻坚框架与 10 月的地方落地
国家发展改革委等五部门《关于开展重点行业节能降碳改造攻坚三年行动的通知》(发改环资〔2026〕698号,2026 年 5 月 18 日印发、6 月 15 日对外发布)明确:自 2026 年起,以钢铁、电解铝、水泥、平板玻璃、炼油、乙烯、合成氨、甲醇、煤电等 9 个行业为重点,用 3 年时间全面实施节能降碳改造,推动企业能效碳效水平应提尽提;到 2028 年底,上述工业重点行业达到现行能效标杆水平的产能比例平均提高 20 个百分点,能效基准水平以下产能基本清零,2028 年起视情拓展实施范围。
产能侧的口径同样清晰。10 月 20 日国新办发布会上,工业和信息化部提出深化产能治理,实施重点产品产能风险监测预警,严格执行电解铝产能置换政策,严控氧化铝、铜等冶炼新增产能,修订铜、铝等行业规范条件,坚决遏制低水平重复建设;同时提出制定《人工智能+有色金属行业实施指南》与行业标准体系建设指南。新增产能受控、存量产线要提效,两者叠加,投资重心自然落到改造而非新建。
落地层面,四川省发展和改革委员会等五部门于 2026 年 10 月 27 日公开《四川省重点行业节能降碳改造攻坚三年行动方案》(川发改环资〔2026〕358号,文件落款 8 月 25 日)。方案要求各市(州)全面摸排企业能源消费量、单位产品综合能耗与主要装置能效水平,制定改造计划清单并把任务落实到具体企业,每年 11 月底前报送进展;能效未达到强制性能耗限额标准限定值和基准水平的项目应于 2028 年底前完成改造,不能按期完成或改造后仍不达标的项目按规定淘汰关停。电解铝条目另设目标:到 2028 年底,能效标杆水平以上电解铝产能占比达到 50% 以上。
二、政策文本点名的装置清单
四川方案对电解铝行业列出的技术条目相当具体,可按专业归为五类。它不是一份采购清单,而是改造方向的枚举,且几乎全部指向既有槽系列的局部更新与加装。
| 类别 | 政策文本点名内容 | 对应环节 |
|---|---|---|
| 槽体与内衬 | 新型稳流保温铝电解槽、石墨化阴极、高质量阳极、电解槽上部集气密闭,推广 500kA 及以上大型电解槽 | 电解槽本体、阴/阳极、烟气收集 |
| 通用用能设备 | 电机、风机、水泵、热泵、空压机、变压器更新升级 | 动力与辅助系统 |
| 整流与热回收 | 高效整流设备,烟气余热高效回收与梯级利用,低温余热发电 | 供电效率、余热利用 |
| 控制与检测 | 智能槽控系统、在线监测装备、多功能智能天车 | 过程控制、计量、起重搬运 |
| 能源结构 | 通过绿证绿电交易、建设可再生能源发电项目提高绿电消费比例 | 负荷、计量与溯源 |
值得注意的是清单的结构:机械本体(保温、稳流、阴极、阳极、集气密闭)与用能设备更新并列,控制、监测、天车等智能化装备被单独列出,余热回收与绿电消费则把改造边界延伸到能源侧。这意味着改造项目的评价不再只看槽型或单机产能,而要看电耗、集气效率与数据可核查性是否同时改善。
三、现状与目标之间的差距
协会 10 月 30 日发布会披露的行业现状,可以用来判断改造的现实起点:2025 年电解铝综合交流电耗降至 13202 千瓦时/吨,比全球平均水平低 750 千瓦时/吨以上;500kA 及以上大型电解槽产能占比超 45%;电解铝能效标杆水平以上产能占比约 30%;行业可再生能源利用比例提升至 27.7%,较「十三五」末提高 7.9 个百分点;再生有色金属产量首次突破 2000 万吨,约占十种常用有色金属总量的四分之一;国内电解铝消纳的绿电占比约 30%;铝行业已于 2024 年提前 6 年实现碳达峰。
标准与核算体系同步推进:行业已发布工业领域首项碳足迹量化国家标准《温室气体 产品碳足迹量化方法与要求 电解铝》,并正推进氧化铝、电解铝等重点品种能耗和碳排放限额强制标准修订;截至发布会,已有 18 家骨干企业申报国家级零碳工厂,重点通过绿电直连、工艺优化、余热回收、数字化能碳管控推进源头减碳与过程脱碳。
把「全国现状约 30%」与「四川 2028 年底 50% 以上」并排看,提升空间约 20 个百分点,与 698 号文「平均提高 20 个百分点」的量级一致。但两者一个是全国行业现状、一个是省级目标,口径并不相同,只能作方向性对照,不能当作同一张表里的减法。真正的难点协会也讲得很直接:风光资源与电解铝产能空间错配、新能源供电存在间歇性、专线配套投资高、绿电溯源核算机制有待完善、绿电铝的绿色溢价未充分体现。前三项是工程与投资问题,后两项则要求计量、溯源与在线监测能力,这恰是清单里「智能槽控系统、在线监测装备」被写进政策的原因。
四、对装备与备件环节的四点观察
- 需求形态改变。产能置换约束新增整线,改造需求以既有车间局部更新为主,交付更接近「单机+部件+调试+数据接口」的组合,而非整厂总包;这对模块化设计、现场适配与停机窗口安排提出更高要求。
- 验收口径改变。当综合交流电耗、能效标杆、碳排放因子成为考核项,技术规格书更容易写入可测量、可记录、可上传的条件,槽控系统、在线监测与能源/碳排放管理系统会与机械改造捆绑验收。
- 阳极质量仍是降耗抓手。「高质量阳极」「石墨化阴极」被写进电解铝改造条目,与本栏目此前讨论的铁—碳压降成因链条是同一逻辑:钢爪清理、磷生铁成分与夹杂、碳碗清洁、涂层与浇注质量决定接触电阻,槽体改造的收益最终要靠界面质量兑现。对应到设备侧,残极与磷铁环压脱、抛丸清理、碳碗与铁水包烘干、蘸石墨、导杆校直等工位的状态及其易损件,常是改造项目里被低估的一环。
- 工期受检修窗口约束。方案要求企业结合停工检修时机安排改造时序、每年 11 月底前报送进展,改造往往与年度检修合并。备件与易损件的排产周期、供货连续性对工期的影响,可能大于设备本体制造周期。
五、引用与使用提示
698 号文是全国三年框架,四川方案是省级落地要求,协会发布会是行业运行与能效现状,工信部表述是产能治理方向,四者适用范围与统计区间不同,引用时应标注发布方与日期,不要把省级目标当成全国强制指标,也不要把 2025 年电耗数据与 2026 年月度产量混用。本文只整理公开政策文本与行业发布内容,不列任何供应商、外协厂、采购品牌名单、中标结果或金额,也不提供针对具体产线的工艺参数;实际改造方案应以企业节能诊断、现场化验与工艺卡为准。本文为公开资料整理与独立行业观察,不构成投资、采购或技术建议,文中信息不属于北京博寿冶金技术贸易有限公司的业务、客户或业绩。
This note focuses on two verifiable public documents released in late October 2026: the provincial three-year energy-saving and carbon-reduction retrofit plan published by Sichuan authorities on 27 October, and the Q&A transcript of the China Nonferrous Metals Industry Association's press conference on third-quarter operating conditions held on 30 October. Both are placed in the context of the national three-year retrofit programme. Policy texts, industry operating data and provincial targets come from different publishers and different statistical scopes, so each figure below is labelled and none is mixed with another.
1. The national framework and its October implementation
The Notice on Carrying Out a Three-Year Campaign for Energy-Saving and Carbon-Reduction Retrofits in Key Industries (Fa Gai Huan Zi [2026] No. 698), issued jointly by the National Development and Reform Commission and four other ministries on 18 May 2026 and published on 15 June, designates nine priority sectors: steel, electrolytic aluminium, cement, flat glass, refining, ethylene, synthetic ammonia, methanol and coal-fired power. From 2026, three years of comprehensive retrofits are to be carried out so that enterprises raise energy and carbon efficiency wherever feasible. By the end of 2028, the share of capacity at or above the current energy-efficiency benchmark level in these industrial sectors should rise by an average of 20 percentage points, capacity below the baseline level should be essentially eliminated, and the scope may be widened from 2028 onwards.
The capacity side is equally explicit. At a State Council Information Office briefing on 20 October, the Ministry of Industry and Information Technology said it would deepen capacity governance through risk monitoring and early warning for key products, strictly enforce the capacity-swap policy for electrolytic aluminium, tightly control new alumina and copper smelting capacity, revise industry standards for copper and aluminium and curb low-level redundant construction. It also announced guidelines for 'AI plus non-ferrous metals' and for the sector's standards system. With new capacity constrained and existing lines required to improve efficiency, investment naturally shifts towards retrofits rather than greenfield lines.
At implementation level, five Sichuan provincial departments published the Sichuan Three-Year Action Plan for Energy-Saving and Carbon-Reduction Retrofits in Key Industries on 27 October 2026 (Chuan Fa Gai Huan Zi [2026] No. 358; the document itself is dated 25 August). Municipalities are required to survey enterprises' energy consumption, unit-product energy use and the efficiency of major installations, draw up retrofit lists with tasks assigned to individual plants, and report progress by the end of November each year. Projects that do not meet the mandatory energy-consumption limit or baseline level must complete retrofits by the end of 2028; those that fail to do so, or still fall short afterwards, are to be closed under applicable rules. For electrolytic aluminium the plan sets a separate target: by the end of 2028, more than 50% of capacity should be at or above the energy-efficiency benchmark level.
2. The equipment named in the policy text
The electrolytic aluminium section of the Sichuan plan is unusually specific. Grouped by discipline, its technical items fall into five categories. It is not a purchasing list but an enumeration of retrofit directions, and almost every item points to partial replacement or add-on installation on an existing potline.
| Category | Items named in the plan | Corresponding area |
|---|---|---|
| Cell body and lining | New stable-current insulated aluminium reduction cells, graphitised cathodes, high-quality anodes, upper gas-collection enclosure, and adoption of 500 kA and larger cells | Cell body, cathode/anode, fume capture |
| General energy-using equipment | Upgrading of motors, fans, pumps, heat pumps, air compressors and transformers | Power and auxiliary systems |
| Rectification and heat recovery | High-efficiency rectifiers, efficient cascade recovery of flue-gas waste heat, low-temperature waste-heat power generation | Power conversion efficiency, heat recovery |
| Control and instrumentation | Intelligent cell control systems, on-line monitoring equipment, multi-function intelligent overhead cranes | Process control, metering, lifting and handling |
| Energy mix | Higher green-power consumption through green certificate and green power trading and on-site renewable generation | Load, metering and traceability |
The structure of this list matters. Mechanical items (insulation, current stability, cathode, anode, gas-collection enclosure) sit alongside general equipment upgrades; control, monitoring and crane systems are listed separately; heat recovery and green power extend the retrofit boundary into the energy system. A project is therefore no longer judged only by cell type or nominal unit output, but by whether specific electricity consumption, fume-collection efficiency and data verifiability improve together.
3. The gap between current performance and the targets
The association's 30 October briefing describes the starting point: in 2025, comprehensive AC electricity consumption for electrolytic aluminium fell to 13,202 kWh per tonne, more than 750 kWh/t below the global average; cells of 500 kA and above accounted for over 45% of capacity; capacity at or above the energy-efficiency benchmark level stood at about 30%; renewable energy use across the sector rose to 27.7%, up 7.9 percentage points from the end of the Thirteenth Five-Year period; recycled non-ferrous metal output exceeded 20 Mt for the first time, roughly a quarter of the ten major non-ferrous metals; green power consumed by domestic aluminium smelters was about 30%; and the aluminium sector reached its carbon peak in 2024, six years ahead of schedule.
Standards and accounting are advancing in parallel. The sector has published the first national standard for product carbon-footprint quantification in industry, covering electrolytic aluminium, and is revising mandatory energy-consumption and carbon-emission limits for key products including alumina and electrolytic aluminium. As of the briefing, 18 leading enterprises had applied for national-level zero-carbon factory status, focusing on direct green-power supply, process optimisation, waste-heat recovery and digital energy and carbon management.
Setting a national figure of roughly 30% against a provincial target of more than 50% by end-2028 suggests about 20 percentage points of headroom, consistent with the 20-point average increase in the national notice. The two numbers are nevertheless different in scope: one is a nationwide industry snapshot, the other a provincial target, so they support a directional comparison, not an arithmetic subtraction. The association also named the practical obstacles to direct green-power supply: a geographic mismatch between wind and solar resources and smelter capacity, intermittency of renewable supply, high dedicated-line investment, incomplete green-power traceability and accounting rules, and an insufficient green premium for low-carbon aluminium. The first three are engineering and capital problems; the last two require metering, traceability and on-line monitoring, precisely why intelligent cell control and on-line monitoring equipment appear in the retrofit list.
4. Four observations for equipment and spare parts
- Demand shape changes. With capacity swaps constraining new potlines, retrofit demand concentrates on partial upgrades of existing workshops. Delivery looks more like a combination of individual machines, components, commissioning and data interfaces than a full turnkey plant, which raises the bar for modular design, on-site adaptation and scheduling around shutdown windows.
- Acceptance criteria change. Once specific electricity consumption, benchmark efficiency and emission factors become assessment items, technical specifications tend to require measurable, recordable and uploadable data. Cell control systems, on-line monitoring and energy/carbon management systems become part of the acceptance package alongside mechanical work.
- Anode quality remains a lever. 'High-quality anodes' and 'graphitised cathodes' appear in the electrolytic aluminium section of the plan for the same reason discussed in our earlier technical note on the iron-to-carbon voltage drop: claw cleaning, cast-iron composition and inclusions, carbon-bowl cleanliness, coating and pouring quality determine interfacial contact resistance, and the benefit of a cell retrofit is ultimately realised at that interface. On the equipment side, the condition and wear parts of stations for butt and cast-iron ring stripping, shot blasting, carbon-bowl and ladle drying, graphite dipping and rod straightening are often underestimated in retrofit projects.
- Schedules are bound by maintenance windows. The plan asks enterprises to arrange retrofit timing around planned shutdowns and to report progress by the end of November, so retrofits are commonly combined with annual maintenance. Lead times and continuity of supply for spare parts and consumables can influence the schedule more than the fabrication time of the main equipment.
5. How to cite and use this material
The national notice sets a three-year framework, the Sichuan plan is a provincial implementation requirement, the association briefing reports industry performance, and the ministry statement describes capacity governance. Their scopes and reference periods differ: label the publisher and date when citing, do not treat a provincial target as a nationwide mandatory indicator, and do not combine 2025 electricity-consumption figures with 2026 monthly output data. This article compiles only public policy texts and published industry information. It lists no suppliers, subcontractors, purchasing brand lists, award results or contract values, and offers no process setpoints for any specific line; actual retrofit schemes should rest on a site energy audit, laboratory analyses and process cards. This is an independent compilation of public information, not investment, procurement or engineering advice, and the information here is not the business, clients or track record of Beijing Brochot Metallurgical Technology & Trading Co., Ltd.