11 月 9 日本栏目整理过四则阳极组装相关采购公告的要点。这一篇换一个观察角度:不逐条复述买了什么,而是看采购是怎样被组织起来的。把 2026 年 10 月下旬至 11 月上旬公开的几组公告并排读,会看到三种差别明显的方式——存量车间按工位拆成独立小包、新建产线按整线能力交钥匙总承包、集团集中招标把研发与年度备件框架打包成批次。另有两则容易被忽略的材料:一份把易损件写成可测量参数的竞价清单,以及一份采购终止公告。以下只整理公告要点与技术条目,信息以原公告为准,不属于本公司的业务、客户或业绩;不列中标结果、金额或任何供货企业。
一、工位拆包:存量车间改造的分区节奏
同一电解铝企业电解二厂阳极组装车间改造项目,在 10 月至 11 月连续放出多个彼此独立的询比采购包。前一篇已记录碳碗烘干机及铁水包烘干机、蘸石墨机两包;新公开的两包分别是斗式提升机、带式输送机、电动下料装置(11 月 5 日发布),以及起重机维修(响应文件开启时间为 11 月 11 日)。
| 采购包 | 公告载明的主要内容 | 公告时间 |
|---|---|---|
| 斗式提升机、带式输送机、电动下料装置 | 1 台斗式提升机的安装及调试;2 套电解质料仓仓底配套下料装置,含 2 台手动阀、2 台电动物料切断阀、2 台电动伸缩下料器;1 台带式输送机的安装及调试;具体要求见采购文件技术要求章节 | 2026-11-05 |
| 起重机维修 | 阳极组装车间改造项目项下的起重机维修,询比采购,公告载明报价截止与开启时间、CA 客户端报价与在线解密流程 | 2026-10(开启 11-11) |
| 碳碗烘干机及铁水包烘干机 | 烘干主机、移动式铁水包烘干机及回收房,配套燃控、气动与 PLC 自控(见本栏目 11 月 9 日一篇) | 2026-10 |
| 蘸石墨机 | 询比采购,同步发布于企业电子采购平台与公共服务平台(见本栏目 11 月 9 日一篇) | 2026-10 |
拆包方式本身就是信息。四个包分别对应物料输送与下料、起重搬运、浇注前烘干、钢爪蘸石墨,恰好覆盖阳极组装车间的工位链条,而没有任何一个包是新建整线。公告还写明输送一包采用询比采购、仅随响应文件一轮次报价、此后不再议价,并对供应商设专业承包资质等级、近三年安全与环境事故记录、不接受联合体等门槛。这种按工位分期放包、每包单独资格后审的做法,更接近存量车间分区停机、逐段改造的施工组织,而非一次性交钥匙工程。对备件与检修的含义是:改造窗口被切成多段,单包的接口匹配(下料装置与料仓仓底配套、输送与既有产线对接)比设备本体参数更容易成为风险点。
二、交钥匙总承包:钢爪摩擦焊产线买的是能力
与拆包相对的另一极,是 10 月 23 日发布、11 月 13 日开标的铝业钢爪摩擦焊项目第一批次加工设备采购。两个标段分别为 450T 阳极钢爪惯性摩擦焊设备 1 台/套与高速金属圆锯机 1 台/套,均为交钥匙总承包,包含设计、制造、供货、运输、安装、调试、工艺服务、培训与验收。
- 工艺要求写进规格:一标段设备须同时满足钢—钢、钢—铝两种摩擦焊工艺,并要求提供全套焊接工艺评定、工艺规程及现场工艺技术支持。
- 联动要求:二标段圆锯机需与惯性摩擦焊设备出料联动,满足坯料定尺锯切与自动化上料衔接。
- 产能与节奏:公告载明投产后两班制,月度产能目标 720 组、年度最少 8640 组,计划 2027 年 6 月投产,设备安装于阳极车间改造厂房内。
- 交付与质量门槛:两标段交货期分别为预付款到账后 180 与 90 日历天,最终验收合格起质保 12 个月;设备须为全新未使用、不接受试制性质整机或部件,并要求适应现场工况长期连续运行;投标人须为所投标段设备的原厂制造方,并具有同等级别(公称顶锻力不低于 400 吨)设备的既有业绩。
值得注意的不是摩擦焊这项工艺本身,而是采购标的的定义方式:验收对象包含产能目标、工艺评定文件、两台设备之间的出料联动与操作培训,而不只是单台机器的铭牌参数。对关注阳极组装备件的一方,这类项目意味着钢爪这一连接件的制造路线可能从铸造或焊补转向摩擦焊复合结构,后续钢爪校直、导杆组对与爪头尺寸链的备件口径也会随之变化。公告中的产能目标与工期均为发布方自述的采购要求,不是已实现的运行结果。
三、集中招标:研发、维修与年度备件框架同批打包
11 月 5 日公开的某能源集团 2026 年度第 87 批集中招标(一)公告列出 8 个标段,把性质完全不同的需求放在同一批次里,其中与阳极组装和电解槽运维直接相关的有 6 项。
| 标段 | 公告载明范围 | 期限或交付节奏 |
|---|---|---|
| 数值仿真及智能控制耦合研发 | 面向大型铝电解槽复杂工况,研究多物理场耦合机理与动态响应,构建并校核数值模型;研究关键运行信息分布式获取、融合与状态辨识,形成兼顾效率、能耗与稳定性的优化方法;研发自主可控智能控制平台及配套装备 | 合同签订起至 2028-12-31;公告另列专利、论文与软件著作权产出要求 |
| 炭素分厂煅烧原料库运行维护外委 | 原料库系统及附属设施的运行、维护、保养、巡视与卫生清理,含残极筛下料、除尘器收尘粉排放与收集等作业 | 计划 1096 日历天(2027-01-15 至 2030-01-14) |
| 磷铁环、残极压脱机维修 | 两类压脱机损坏、磨损零部件的维修更换,设备基础及辅助设备维修更换 | 总工期 180 天,分踏勘与方案、备件到货、现场维修与验收三段 |
| 新增甩链清理机 | 1 台钢爪表面甩链清理机与 1 台阳极表面甩链清理机的供货及安装调试,含原设备拆除运输、悬链系统改造对接、停止器与轨道等附属设施、电气控制系统接入原有系统,并利用原除尘器、改造管道收尘 | 总工期 210 天 |
| 2027 年总包配送磷生铁 | 磷生铁 3 项,年度框架式的总包配送 | 接到采购订单起 30 日内交货 |
| 2027 年总包配送电解槽气缸设备 | 电解槽气缸设备 7 项,年度框架式的总包配送 | 接到采购订单起 90 日内交货 |
这一批次里最值得记录的是采购颗粒度的两端:一端是横跨数年的仿真与控制平台研发,另一端是把磷生铁(浇注耗材)与气缸设备(通用备件)写成按订单 30 日或 90 日交货的年度总包配送条目。备件与耗材从随坏随买转成框架式供应,直接改变库存与供货周期的管理方式。新增甩链清理机标段则明确要求接入原有控制系统、利用原有除尘器并改造收尘管道,是存量改造中接口约束重于本体参数的典型写法。
四、易损件验收正在参数化
11 月 2 日一份工业专用设备及配件网上竞价公告,把阳极组装常用易损件写成了可测量的技术条目,可作为备件采购规格书的参考样例。
| 条目 | 公告载明的技术条件 |
|---|---|
| 磷铁环压脱机下部油缸支撑座及油缸总成 | 压脱力 3000KN;支撑底板最薄处不低于 100mm,材质 Q235 或 ZG230-450;中心偏移误差不超过 ±3mm;配铜导向套与导向体;油缸工作压力 32MPa、杆径 D220、行程 S≥280mm、活塞直径 400mm、聚氨酯密封件;参照 GB 50272-2009;到货验收合格后现场安装,标注使用寿命 720 天 |
| 磷铁环压脱机上部钳口机体总成 | 夹紧装置与滑块材质不低于 ZG230-450,钳口保护板 45#,销轴 42CrMo;更换夹紧油缸行程不小于 170mm、工作压力 12.5MPa、缸径不低于 70mm;机体紧固螺丝不低于 8.8 级 |
| 软残极抛丸机顶衬板、端衬板、叶片架 | 耐磨铸铁,分别 110 个、12 个、10 套,标注使用寿命 90 天,参照 GB/T 24597-2009;验收要求无明显孔眼、裂纹及影响外观与强度的表面、形状缺陷 |
把材质牌号、形位公差、液压参数、参照标准与预期寿命同时写进竞价清单,说明验收依据正在从按图号供货转向按参数与寿命验收。对备件管理而言,这类条目可以直接转成到货检验表;但也要注意,寿命数字是公告中的预期值,实际消耗速率取决于压脱频次、铁渣板结程度与清理工位状态,不能当作通用消耗定额。
五、公告状态不是静态的
同在 11 月 5 日,某工程公司境外项目残极压脱机及磷铁环压脱机采购发布了终止公告(招标编号 0026-ZB10976),说明因招标计划发生变化,经招标人决定终止本次招标。做需求观察时如果只累计新发公告、不跟踪变更与终止,就会把已经撤销的需求仍然算在管线里。本栏目仅记录公告状态,不推测原因,也不发布任何中标结果。
六、使用提示
- 不同集团使用各自的电子采购平台,报名、文件获取、CA 登录、客户端报价与在线解密流程各异,转载站点可能只保留摘要或删节关键字段,核对务必回到原发布平台。
- 询比采购常见一次性报价、不再议价,且普遍设资格后审、业绩、安全记录与项目经理及安全员资质要求,多不接受联合体。
- 公告中的技术参数、数量、工期与产能目标均为发布方自述的采购要求,不是行业平均数据,也不是已实现的运行结果。
本栏目为公开资料整理与独立观察,仅供参考,不构成投资、采购或技术建议。文中涉及的招标信息以原公告为准,不属于本公司的业务、客户或业绩,也不代表任何招标人、采购机构或发布平台的立场。
On 9 November this column summarised four procurement notices related to anode assembly. This note changes the angle: instead of listing what was bought, it asks how the purchasing itself was organised. Reading several groups of notices published between late October and early November 2026 side by side reveals three clearly different structures, plus two items that are easy to overlook. Only notice highlights and published technical entries are reproduced here. Information is subject to the original notices and does not represent our company's business, clients or track record; no award results, contract values or supplying companies are listed.
1. Station-by-station lots: the rhythm of an existing-workshop retrofit
One aluminium smelter's No.2 anode assembly workshop retrofit has produced a series of separate enquiry-based lots through October and November. The previous note recorded the carbon-bowl dryer plus hot-metal ladle dryer lot and the graphite-dipping machine lot. Two further lots have since appeared: a bucket elevator, belt conveyor and electric discharge devices lot (published 5 November), and a crane maintenance lot (response opening on 11 November).
| Lot | Scope stated in the notice | Notice date |
|---|---|---|
| Bucket elevator, belt conveyor, electric discharge devices | Installation and commissioning of one bucket elevator; two sets of discharge devices for electrolyte silo bottoms, comprising two manual valves, two motorised material cut-off valves and two telescopic discharge units; installation and commissioning of one belt conveyor. Detailed requirements are in the technical chapter of the procurement documents | 2026-11-05 |
| Crane maintenance | Crane maintenance under the same anode assembly workshop retrofit, enquiry-based, with stated pricing deadline and opening time, CA client quotation and online decryption procedures | Oct 2026 (opening 11 Nov) |
| Carbon-bowl and hot-metal ladle dryers | Drying unit, mobile ladle dryer and recovery enclosure with combustion control, pneumatics and PLC automation (see our 9 November note) | Oct 2026 |
| Graphite-dipping machine | Enquiry-based, published on the corporate e-procurement platform and a public service platform (see our 9 November note) | Oct 2026 |
The way the work is split is itself informative. The four lots cover material conveying and discharge, lifting and handling, pre-pour drying, and graphite dipping of the steel claw — essentially the station chain of an anode assembly workshop — and none of them is a complete new line. The conveying lot is explicitly an enquiry purchase with a single round of pricing attached to the response documents and no subsequent negotiation, with qualification requirements covering contractor grade, safety and environmental records over the past three years, and a bar on consortia. Lot-by-lot post-qualification of this kind is much closer to sectional shutdown and phased retrofit than to a turnkey project. For spare parts and maintenance planning, the implication is that the shutdown window is cut into several segments, and interface fit — discharge devices mating with existing silo bottoms, conveyors tying into an existing line — is a more likely source of risk than the nameplate parameters of any single machine.
2. Turnkey supply: buying capability rather than a machine
At the opposite extreme is the first batch of processing equipment for a steel-claw friction-welding project, published on 23 October with opening on 13 November. Two lots cover one 450T inertia friction-welding machine for anode steel claws and one high-speed metal circular saw, both as turnkey packages including design, manufacture, supply, transport, installation, commissioning, process service, training and acceptance.
- Process requirements written into the specification: the welding machine must satisfy both steel-to-steel and steel-to-aluminium friction-welding processes, with a full set of welding procedure qualifications, procedure specifications and on-site process support.
- Interlocking: the saw must link to the discharge of the welding machine to support cut-to-length billet sawing and automated feeding.
- Throughput and timing: the notice states two-shift operation, a monthly target of 720 sets and a minimum annual output of 8,640 sets, planned commissioning in June 2027, with equipment installed in an anode workshop retrofit building.
- Delivery and quality gates: delivery periods of 180 and 90 calendar days after the advance payment, a 12-month warranty from final acceptance, brand-new unused equipment with no prototype machines or components accepted, continuous operation under local site conditions, and a requirement that bidders be the original manufacturer of the equipment with prior references at comparable rating (nominal upset force of at least 400 tonnes).
What matters here is not the welding process as such but how the scope is defined. Acceptance covers a throughput target, procedure qualification documents, discharge interlocking between two machines and operator training — not merely the nameplate data of one unit. For anyone tracking anode assembly wear parts, a project of this type suggests the manufacturing route for the steel claw may shift from casting or repair welding towards a friction-welded composite structure, which would in turn change the dimensional chain and spare-part definitions for claw straightening and rod assembly. The throughput targets and delivery periods are the purchaser's stated requirements, not achieved operating results.
3. Centralised tendering: research, maintenance and annual spare-parts frameworks in one batch
A centralised tender batch published on 5 November lists eight lots that place very different kinds of demand side by side. Six of them relate directly to anode assembly and cell operation.
| Lot | Scope stated in the notice | Duration or delivery cadence |
|---|---|---|
| Numerical simulation and intelligent control coupling research | Multi-physics coupling mechanisms and dynamic response for large aluminium reduction cells, building and validating numerical models; distributed acquisition, fusion and state identification of key operating data; optimisation methods balancing efficiency, energy use and stability; an autonomous controllable control platform and associated equipment | From contract signing to 2028-12-31; the notice also sets patent, paper and software copyright deliverables |
| Outsourced operation and maintenance of a carbon-plant calcined-material warehouse | Operation, maintenance, inspection and cleaning of the warehouse system and ancillary facilities, including butt screening fines and dust-collector powder discharge and collection | Planned 1,096 calendar days (2027-01-15 to 2030-01-14) |
| Repair of cast-iron-ring and butt stripping machines | Repair and replacement of damaged or worn components of both stripping machines, plus equipment foundations and auxiliary equipment | 180 days total, split into survey and method statement, parts delivery, on-site repair and acceptance |
| New chain-type cleaning machines | Supply, installation and commissioning of one steel-claw surface cleaner and one anode surface cleaner, including removal and transport of existing equipment, overhead-chain modification and interfacing, stops and rails, electrical control tied into the existing system, and reuse of the existing dust collector with modified ducting | 210 days total |
| 2027 framework supply of phosphorous cast iron | Three items of cast iron under an annual framework arrangement | Delivery within 30 days of a purchase order |
| 2027 framework supply of cell cylinder equipment | Seven items of cylinder equipment under an annual framework arrangement | Delivery within 90 days of a purchase order |
The most useful observation is the span of granularity within one batch: at one end, a multi-year simulation and control platform research contract; at the other, annual framework line items that commit consumable cast iron and general cylinder spares to delivery within 30 or 90 days of an order. Moving spares and consumables from ad hoc replacement purchases to framework supply changes how inventory and lead times are managed. The chain-cleaner lot is also a good example of retrofit scoping, since it explicitly requires interfacing with the existing control system and dust collector — interface constraints weigh more heavily than the nameplate data of the new machines.
4. Wear parts are increasingly specified by measurable parameters
A competitive-quotation notice for industrial special equipment and spare parts, dated 2 November, turns common anode assembly wear items into measurable technical entries and is a useful reference for how a spare-parts specification can be written.
| Item | Technical conditions stated in the notice |
|---|---|
| Lower cylinder support seat and cylinder assembly of a cast-iron-ring stripping machine | Stripping force 3000 kN; support plate at least 100 mm at its thinnest point, material Q235 or ZG230-450; centre offset tolerance within ±3 mm; copper guide bush and guide body; cylinder working pressure 32 MPa, rod diameter D220, stroke S≥280 mm, piston diameter 400 mm, polyurethane seals; reference standard GB 50272-2009; on-site installation after incoming acceptance, stated service life 720 days |
| Upper jaw body assembly of a cast-iron-ring stripping machine | Clamping device and slide of at least ZG230-450, jaw protection plates of 45# steel, pins of 42CrMo; replacement clamping cylinder with stroke not less than 170 mm, working pressure 12.5 MPa, bore not less than 70 mm; body fasteners of grade 8.8 or above |
| Top liners, end liners and blade carriers for a soft-butt shot-blasting machine | Wear-resistant cast iron, 110 pieces, 12 pieces and 10 sets respectively, stated service life 90 days, reference standard GB/T 24597-2009; acceptance excludes visible porosity, cracks and surface or shape defects affecting appearance and strength |
Material grades, geometric tolerances, hydraulic parameters, reference standards and expected service life all appearing in one quotation list shows that acceptance is shifting from supply by drawing number towards verification by parameter and service life. For spare-parts management, entries like these can be converted directly into an incoming inspection checklist. The life figures, however, are the purchaser's expectations: actual consumption depends on stripping frequency, the degree of slag build-up and the condition of the cleaning station, so they should not be treated as general consumption norms.
5. Notice status is not static
Also on 5 November, a termination notice was published for a procurement of butt-stripping and cast-iron-ring stripping machines for an overseas project (tender no. 0026-ZB10976), stating that the tender had been terminated because the procurement plan had changed. A demand tracker that only counts newly published notices and never follows amendments or terminations will keep withdrawn requirements in its pipeline. This column records notice status only, does not speculate on reasons and publishes no award results.
6. Practical notes
- Each group runs its own e-procurement platform, with different registration, document access, CA login, client-side quotation and online decryption procedures. Aggregator sites may retain only an abstract or omit key fields, so verification must return to the original publishing platform.
- Enquiry-based purchases commonly allow one round of pricing with no further negotiation, and typically set post-qualification, track record, safety records and project manager or safety officer credentials, with consortia frequently excluded.
- Technical parameters, quantities, durations and throughput targets in notices are the purchaser's stated requirements, not industry averages and not achieved operating results.
This column is a compilation of public information and independent industry commentary, for reference only; it is not investment, procurement or engineering advice. The tender information mentioned here is subject to the original notices, does not represent our company's business, clients or track record, and does not reflect the position of any tenderee, procurement agency or publishing platform.