本栏目此前的两篇技术文章,分别梳理了铁—碳压降的成因链条(11 月 8 日)与磷生铁清渣工位的自动化改造(11 月 11 日),观察对象都是「组装出来的阳极」。这一篇把视角移到另一类对象:反复回用的金属件——阳极导杆组与钢爪。它们每循环一次都要经历残极与磷铁环压脱、抛丸与清刷、矫直、检测、焊补,直到截面损失或变形超出限值才报废。2026 年 10 月中旬至 11 月上旬公开的几组材料,恰好覆盖这条回用链上三个不同环节:一项 11 月 10 日授权的实用新型专利、一项 11 月 10 日公开的设备工程评选成果、以及一项 10 月 14 日报道的材料与表面工程评价。以下按工位顺序整理公开技术条目,并说明它们对备件与验收的含义;所有数字均标注出处与口径,单项成果的自述指标不作为行业平均值。
一、回用链:分离工位决定后面要修多少
典型的阳极组装回用路径是:从电解槽返回的残极经装卸站进入,先做电解质清理与残极抛丸,再由残极压脱机把残极块从钢爪上分离,随后磷铁环压脱机把各爪上的磷铁环剥落,铁环经清理滚筒去除残余砂与氧化皮后回炉;脱开后的导杆组进入清刷、导杆矫直、钢爪抛丸与矫直,再经蘸石墨、在线烘干,最后到浇注站与新炭块组装,悬链输送系统把各工位串成连续流水线。
压脱是分离而不是成形,但分离方式直接决定金属件后续要修多少。钢爪在液压冲击、夹持反力与偏载下会出现爪头变形、钢梁磨损与焊缝疲劳;爪头一旦变形,残极碎块容易夹在爪间并随磷铁环进入清理滚筒与中频炉,增加炉渣量、降低化铁效率,并让铁水质量波动。一项公开的实用新型专利成果页把传统压脱设备的痛点概括为定位效率低、钢爪夹持不稳、压脱过程易松动,其顶升式结构采用定位板与压力开关协同判定钢爪位置、夹紧座与卡块双重夹紧、液压缸驱动冲头座与多冲头自下而上同步施力,并以螺杆驱动加光轴滑动的复合导向约束移动块以避免偏载;成果页还说明该结构可与现场 PLC 对接,实现自动定位、自动夹紧与自动顶升压脱。这几条恰好给出压脱工位的备件线索:定位与压力检测元件、卡块与夹紧座、液压缸密封、冲头与冲头座、导向光轴与螺杆。该成果页发布于 2026 年 7 月,属较早公开的专利资料,本文只引用其技术结构,不引用其中的应用项目或单位描述。
二、钢梁厚度修复:11 月 10 日授权的专利在解决什么
据 11 月 11 日的一则专利授权报道,国家知识产权局于 2026 年 11 月 10 日公告授权「一种铝电解阳极导杆组钢梁厚度修复机构」,授权公告号 CN224951238U,申请号 CN202521997591.4,申请日 2025 年 9 月 17 日,分类号涉及焊接辅助装置与焊接定位(B23K37/00、B23K37/04、B23K103/04)。专利摘要给出的构成是:底座上设上料机构与阳极导杆组件固定机构;上料机构由装在底座面板上的横向送料机构、装在横向送料机构上的竖向送料机构、以及装在竖向上部面板的待焊件固定槽组成;固定槽内连接槽形待焊件,槽形待焊件与阳极钢爪上的待焊阳极钢梁焊接。专利自述的效果是焊接方便、修复成本低,并保证修复后钢爪的使用效果。
把这段摘要翻译成工程语言,问题与解法都很清楚:钢梁在长期循环中因氧化、烧损、压脱冲击与反复打磨而变薄,若按整件报废处理成本过高,因此用一段槽形补件沿钢梁补焊、恢复承载与导电截面;竖向与横向两轴送料解决的是把补件送到焊接位置并保持对中,固定机构解决的是把形状已经不太规则的导杆组稳定夹持。这里的关键词不是「能焊」,而是「重复定位」——补件与母材的贴合间隙、两轴送料的到位精度、焊后截面是否恢复,决定了修复件能否回到自动线上继续使用。
同一则报道附带的公开专利清单还给出一条时间线:发明专利「一种铝电解阳极导杆组钢梁厚度修复方法及装置」(CN121083157A,2025 年 12 月 9 日公布)与本次实用新型同族;更早的有「一种阳极钢爪竖直焊接修复生产系统及方法」(CN117206820B,2024 年 2 月 6 日授权)、「一种阳极导杆自动修复生产设备」(CN219853128U,2023 年 10 月 20 日授权)与「一种阳极导杆自动修复生产线」(CN116237758B,2026 年 6 月 2 日授权);清单中另有「一种新型节能均流阳极钢爪结构」(CN122773425A,2026 年 9 月 18 日公布)与「一种用于常温糊料捣固式的铝电解阳极组装自动扎固装置」(CN122727882A,2026 年 9 月 11 日公布)。把这几项并排看,修复技术已从单件工装走向竖直焊接与自动产线,同时连接工艺本身也在向常温糊料方向探索——后者会改变钢爪与导杆组的受力与损耗模式,值得在评估修复工位投资时一并考虑。
三、在线分拣:把「要不要修、修哪里」变成自动判定
11 月 10 日公开的一项设备工程行业评选结果中,《阳极导杆组在线分拣技术研究与应用》被列为技术成果特等奖,公开表述为瞄准电解铝生产核心工序痛点、破解阳极导杆高效分拣技术难题、显著提升生产现场装备自动化水平。同一批成果还涉及能碳管控的数据算法与铝锭成品线机械手贴标,说明分拣并非孤立单机,而是产线数据链的一环。
对回用链而言,分拣是自动焊补的前置条件。若回用、待修、报废三类不能在线判定,状态不一的导杆组会直接堵在补焊工位:可继续用的被送去焊补是浪费,该报废的被送回产线则把变形与截面不足带入下一次浇注。可测量的判定维度通常包括钢梁剩余厚度、钢爪腿间距与垂直度、导杆弯曲量、爪头变形量、焊缝与表面裂纹;把这些量与件级标识绑定,才能形成「检测—判定—修复—复检」的闭环。需要强调的是,上述判定维度是依据公开技术条目整理的一般性工程观察,并非该成果公开披露的具体参数。
这里还可以和本栏目 11 月 8 日讨论的铁—碳压降接起来:钢爪截面变薄、爪形偏斜会同时抬高接触电阻并造成电流分布不均,因此分拣阈值若只按几何尺寸设定,容易漏掉电性能已经劣化的件。更稳妥的做法是把离线或抽样的压降测量结果与几何判定做周期性比对,用数据校准阈值,而不是把两者当作互不相关的检验项目。
四、从「修」到「少修」:材料与表面工程
10 月 14 日的一则行业报道披露,两项铝电解技术通过行业协会组织的科技成果评价。其中「铝电解节能耐蚀钢爪制备技术及应用」开发出宽温域低电阻抗蠕变的钢爪基材,研制出耐蚀高熵合金涂层材料,并形成基于增材制造的涂层熔覆制备技术;报道称应用后钢爪压降大幅降低,钢爪维修频率下降,现场劳动强度减轻。另一项「铝电解高导低耗炭阳极制备技术及应用」形成炭阳极配方自适应技术,构建颗粒细分、沥青精准配比调节体系与多物料多级配在线检测控制系统,并建立原料—工艺—效用的全生命周期预知与追溯体系;报道给出的自述指标为炭阳极平均电阻率 50 微欧姆·米以下、电解应用后吨铝节能 50 千瓦时以上。
口径必须说清:这些是单项成果在评价材料中给出的指标与结论,不是行业平均值,也未披露统一的槽型、电流密度与统计区间;「整体技术达到国际领先」属于评价结论,不能换算成可外推的运行数据。不同企业的化验方法、槽况与组装工艺差异较大,引用时应回到原始发布材料。
即便如此,方向性含义值得记录。若基材抗蠕变与表面耐蚀能把爪头变形、钢梁烧损的速率压下来,回用链上「修」的频次会下降;但与此同时,件级检测、涂层状态评估、局部熔覆再制造与补件焊接的需求会上升,且对定位精度、工艺评定与复检记录的要求更高。也就是说,需求结构从整件更换迁移到状态判定与局部再制造,而不是总量简单消失。对备件保障而言,判断依据应从「上一周期换了多少件」转为「本周期判定为待修与报废的比例、以及修复件复检合格率」。
五、落到验收与备件的可测量条目
| 环节 | 宜纳入验收或点检的可测量量 | 对应的备件与维护含义 |
|---|---|---|
| 残极与磷铁环压脱 | 液压压力与多冲头同步性、夹持定位重复精度、压脱后爪间残留碎块量 | 液压缸密封、冲头与冲头座、卡块与夹紧座、定位板与压力开关、导向光轴与螺杆 |
| 抛丸与滚筒清理 | 抛丸覆盖率、钢丸循环量、除尘滤芯压差、滚筒漏灰孔堵塞率 | 抛丸器叶片与护板、滤材、滚筒衬板、输送与密封件 |
| 矫直与状态检测 | 冷校后残余变形、钢梁剩余厚度、爪间距与垂直度、压降抽测值 | 校直模具、测厚与视觉检测元件、件级标识与数据接口 |
| 补焊修复 | 补件与母材匹配、两轴送料重复定位精度、焊接工艺评定、焊后截面与导电性 | 槽形补件、焊材与送丝部件、定位夹具、焊后清理工具 |
| 分拣与追溯 | 回用/待修/报废判定阈值、判定一致性、修复件复检合格率 | 识别与读写元件、传感器标定件、数据记录与追溯模块备件 |
以上为公开资料整理与一般性工程观察,不构成针对具体产线的选型、采购或工艺建议;实际阈值应回到本厂设备图纸、化验单与工艺卡。文中涉及的专利、成果与评选信息均以原发布方页面为准,且不属于北京博寿冶金技术贸易有限公司的业务、客户或业绩。
The two earlier technical notes in this column examined the cause chain behind iron-to-carbon voltage drop (8 November) and the automation of cast-iron slag removal (11 November). Both looked at the anode as a finished assembly. This note shifts attention to a different class of object: the metal components reused cycle after cycle, namely the anode rod assembly and its steel claws. Each loop takes them through butt and cast-iron ring stripping, shot blasting and brushing, straightening, inspection and weld repair, until section loss or distortion passes the scrap limit. Several disclosures published between mid-October and early November 2026 happen to cover three separate stages of that reuse chain: a utility model granted on 10 November, an equipment-engineering award result published on 10 November, and a materials and surface-engineering assessment reported on 14 October. What follows organises the published technical items in station order and draws out their implications for wear parts and acceptance criteria. Every figure is labelled with its source and scope; self-reported indicators from a single result are not treated as industry averages.
1. The reuse chain: separation determines the repair load
A typical anode assembly loop starts when butts return from the reduction cells. After unloading, electrolyte is cleaned off and the butts are shot blasted; a butt stripping press separates the carbon from the claws, then a cast-iron ring press removes the rings from all claws at once. The rings pass through a cleaning drum to remove residual sand and scale before returning to the furnace. The freed rod assembly then goes through brushing, rod straightening, claw shot blasting and straightening, graphite dipping and inline drying, and finally reaches the pouring station to be joined with a new carbon block. An overhead chain conveyor links the stations into a continuous line.
Stripping separates rather than forms, yet the way it is done largely determines how much repair the metal parts will need later. Hydraulic impact, clamping reaction and off-axis loading deform claw heads, wear the steel beam and fatigue welds. Once a claw head is deformed, fragments of butt carbon lodge between the claws and travel with the cast-iron rings into the cleaning drum and the medium-frequency furnace, raising slag volume, lowering melting efficiency and destabilising hot-metal quality. A published utility-model result page describes the pain points of conventional equipment as low positioning efficiency, unstable claw clamping and loosening during stripping. Its lifting-type design uses a positioning plate working with a pressure switch to determine claw position, a clamping seat plus blocks for double clamping, and a hydraulic cylinder driving a punch holder with multiple punches upward in synchrony; a screw drive combined with optical-axis sliding guides the moving block so that no off-axis load develops. The page also states that the structure can interface with the plant PLC for automatic positioning, clamping and lifting. Those items map directly onto a wear-parts list for the stripping station: position and pressure sensing elements, blocks and clamping seats, cylinder seals, punches and punch holders, guide shafts and screws. This result page was published in July 2026 and is an earlier public patent source; only its technical structure is cited here, not any application project or organisation described on the page.
2. Steel-beam thickness repair: what the 10 November patent addresses
According to a patent report dated 11 November, the national intellectual property authority granted a utility model on 10 November 2026 titled a mechanism for repairing the thickness of an anode rod assembly steel beam in aluminium electrolysis. Grant publication number CN224951238U, application CN202521997591.4, application date 17 September 2025, with classifications covering welding auxiliary equipment and welding positioning (B23K37/00, B23K37/04, B23K103/04). The abstract sets out a base carrying a feeding mechanism and a rod-assembly fixing mechanism. The feeding mechanism comprises a horizontal feed unit mounted on the base panel, a vertical feed unit mounted on the horizontal one, and a workpiece holding groove mounted on the vertical unit's upper panel. A channel-shaped insert is held in that groove and welded to the beam to be repaired on the anode steel claw. The stated effect is convenient welding, low repair cost and preserved service performance of the repaired claw.
In engineering terms, both the problem and the solution are clear. Over many cycles the beam thins through oxidation, burn-off, stripping impact and repeated grinding. Scrapping the whole assembly is expensive, so a channel-shaped insert is welded along the beam to restore load-bearing and conducting cross-section. The two feed axes exist to bring the insert into position and hold alignment; the fixing mechanism exists to clamp a rod assembly whose geometry is no longer perfectly regular. The decisive word is therefore not weldability but repeatable positioning: fit-up gap between insert and base metal, two-axis repeat accuracy, and whether the post-weld section is genuinely restored determine whether a repaired assembly can go back onto an automated line.
The published patent list accompanying that same report supplies a useful timeline. An invention application for a method and device for repairing anode rod assembly beam thickness (CN121083157A, published 9 December 2025) belongs to the same family. Earlier items include a vertical weld-repair production system and method for anode steel claws (CN117206820B, granted 6 February 2024), an automatic anode rod repair device (CN219853128U, granted 20 October 2023) and an automatic anode rod repair line (CN116237758B, granted 2 June 2026). The list also contains an energy-saving current-equalising anode steel claw structure (CN122773425A, published 18 September 2026) and an automatic ramming device for room-temperature paste anode assembly (CN122727882A, published 11 September 2026). Read together, repair technology has moved from single fixtures towards vertical welding and automatic lines, while the joining route itself is being explored in the direction of room-temperature paste. The latter would change the loading and wear pattern of claws and rod assemblies, and deserves consideration when evaluating investment in a repair station.
3. Online sorting: turning repair decisions into an automatic judgement
An equipment-engineering sector award result published on 10 November lists research and application of online sorting technology for anode rod assemblies as a top-grade technical achievement. The public wording describes it as targeting a pain point in a core aluminium electrolysis process, solving the problem of efficient rod assembly sorting and markedly raising the level of equipment automation on site. Other results in the same batch cover data algorithms for energy and carbon management and robotic labelling on an ingot finishing line, which suggests sorting is not an isolated machine but one node in a production data chain.
For the reuse chain, sorting is a precondition for automated weld repair. Unless reuse, repair and scrap can be decided inline, assemblies in mixed condition pile up at the welding station: serviceable units sent for build-up are wasted effort, while scrap units returned to the line carry distortion and insufficient section into the next pour. Measurable judgement dimensions normally include residual beam thickness, claw leg spacing and perpendicularity, rod bow, claw-head deformation, and weld or surface cracks. Binding those values to a part-level identifier closes the loop of inspect, decide, repair and re-inspect. It should be stressed that these dimensions are general engineering observations drawn from public technical items, not parameters disclosed for that specific achievement.
This also connects back to the iron-to-carbon voltage drop discussed in this column on 8 November. A thinned claw section or a skewed claw raises contact resistance and skews current distribution at the same time, so a sorting threshold based on geometry alone can miss parts whose electrical performance has already degraded. A sounder approach is to compare periodic or sampled voltage-drop measurements against the geometric classification and use the data to calibrate thresholds, rather than treating the two checks as unrelated.
4. From repair towards fewer repairs: materials and surface engineering
An industry report of 14 October states that two aluminium electrolysis technologies passed an assessment organised by an industry association. One, covering preparation and application of energy-saving corrosion-resistant steel claws, developed a claw substrate with low resistivity and creep resistance across a wide temperature range, produced a corrosion-resistant high-entropy alloy coating material, and established additive-manufacturing-based cladding. The report says that after application the claw voltage drop fell substantially, claw maintenance frequency dropped and manual workload was reduced. The other, covering high-conductivity low-consumption carbon anodes, formed an adaptive anode recipe technique, built a system of particle size fractionation and precise pitch proportioning with online multi-material grading detection and control, and established a full-lifecycle traceability framework from raw material through process to effect. Its self-reported indicators are average carbon anode resistivity below 50 microohm-metres and energy savings above 50 kWh per tonne of aluminium in cell operation.
Scope matters. These are indicators and conclusions from a single assessment dossier, not industry averages, and no common cell type, current density or statistical window is disclosed. A judgement that the overall technology reaches an internationally leading level is an assessment conclusion, not an operating figure that can be extrapolated. Assay methods, cell conditions and assembly practice differ widely between plants, so any citation should return to the original published material.
Even so, the directional implication is worth recording. If creep-resistant substrates and corrosion-resistant surfaces slow claw-head deformation and beam burn-off, the frequency of repair on the reuse chain falls. At the same time, demand rises for part-level inspection, coating condition assessment, local cladding refurbishment and insert welding, with tighter requirements on positioning accuracy, welding procedure qualification and re-inspection records. In other words, demand migrates from replacing whole components towards condition judgement and local remanufacture; it does not simply disappear. For spare-parts planning, the useful metric shifts from how many units were replaced last cycle to the share classified as repair or scrap this cycle and the pass rate of repaired units at re-inspection.
5. Measurable items for acceptance and spare parts
| Stage | Measurable quantities for acceptance or inspection | Wear parts and maintenance implications |
|---|---|---|
| Butt and ring stripping | Hydraulic pressure and multi-punch synchrony, clamping repeat accuracy, residual fragment volume between claws | Cylinder seals, punches and punch holders, blocks and clamping seats, positioning plate and pressure switch, guide shafts and screws |
| Shot blasting and drum cleaning | Blast coverage, shot circulation rate, dust filter differential pressure, drum screen-hole blockage | Blast wheel blades and liners, filter media, drum liners, conveyor and sealing parts |
| Straightening and condition inspection | Residual deformation after cold straightening, residual beam thickness, claw spacing and perpendicularity, sampled voltage drop | Straightening dies, thickness and vision sensing elements, part identification and data interfaces |
| Weld build-up repair | Insert to base metal match, two-axis feed repeat accuracy, welding procedure qualification, post-weld section and conductivity | Channel inserts, consumables and wire-feed parts, positioning fixtures, post-weld cleaning tools |
| Sorting and traceability | Reuse / repair / scrap thresholds, decision consistency, pass rate of repaired units at re-inspection | Identification and read-write elements, sensor calibration parts, logging and traceability module spares |
The above is a compilation of public information and general engineering observation, not selection, procurement or process advice for any specific line. Actual thresholds should come from the plant's own drawings, laboratory reports and process cards. Patents, results and award information cited here remain subject to the original publisher's pages and are not the business, clients or track record of Beijing Brochot Metallurgical Technology & Trading Co., Ltd.