本栏目此前三篇技术文章分别看了铁碳压降的成因(11 月 8 日)、磷生铁清渣工位与铁水温度配方(11 月 11 日)、阳极导杆组与钢爪的回用链(11 月 14 日)。这一篇把镜头移到另一侧:残极碳块与电解质离开电解槽之后,在阳极组装车间里留下的烟气、粉尘与返回料。2026 年 11 月 9 日与 11 月 10 日,两份由生态环境主管部门公开的环评文件,把这条常被写成「配套工程」的链条拆成了可数点位的设备清单。下文所有数字与技术条款均标注出处与年度,不同项目口径不拼接;本文为公开资料整理与独立观察,不构成投资、采购或工程建议,与本公司业务、客户或业绩无关。
一、两份 11 月公示:残极侧被拆成可数点位
11 月 9 日一份县级政府网站发布的电解铝项目环评公众参与第一次公示,在建设内容里直接列出:新增 64 台 600kA 预焙阳极电解槽(含对应的超浓相输送系统及废气收集系统)、8 台残极烟气收集装置、2 套覆盖料输送系统、1 套铝灰处理系统;项目明确属产能置换、未新增电解铝产能。值得注意的是,残极烟气收集装置被单独编号计量(8 台),与电解槽自身的废气收集系统并列,而非包含其中。在大型预焙槽的配置里,残极冷却烟气已经不是「随槽烟气一并处理」的附属项,而是有独立设备、独立台数的工艺单元。
11 月 10 日一份省级生态环境部门拟作出的环评批复决定公示,把运营期大气污染源拆得更细:电解槽和残极冷却烟气、覆盖料输送废气、新鲜氧化铝仓与载氟氧化铝仓废气、斗式提升机废气、改造后混合炉废气、搬迁后抬包清理废气。七类点位分别对应不同治理设施,已经接近一份按工序编号的排放清单。
二、三层治理架构:气态污染物、分散产尘点、无组织排放
| 点位(11 月 10 日公示口径) | 治理设施 | 排放去向 |
|---|---|---|
| 新鲜氧化铝仓、载氟氧化铝仓、电解烟气;颗粒物、氟化物、二氧化硫 | 2 套干法脱氟净化系统 + 1 套湿法脱硫净化系统(脱硫塔 2 台,1 用 1 备) | 100 m 高烟囱(2 根排气筒,1 用 1 备) |
| 覆盖料输送系统废气 | 6 套集尘系统 + 6 套布袋除尘器 | 6 根 15 m 排气筒 |
| 斗式提升机输送废气 | 2 套布袋除尘器 | 2 根 15 m 排气筒 |
| 混合炉废气 | 1 套布袋除尘器 | 1 根 15 m 排气筒 |
| 抬包清理废气 | 2 套布袋除尘器(1 用 1 备) | 1 根 20 m 排气筒(1 用 1 备) |
三层结构由此清晰:第一层是气态污染物与细颗粒物,走吸附与吸收的化学、物理净化,服务对象是连续、大风量的电解烟气;第二层是物料转运与清理的机械扬尘,走「就近集气 + 布袋 + 低矮排气筒」,服务对象是分散、间歇的点源;第三层是根本不经过排气筒的无组织排放,靠密闭、负压与作业制度约束。该公示写明各排气筒须满足《铝工业污染物排放标准》(GB25465-2010,含修改单)大气污染物特别排放限值,以及重污染天气重点行业应急减排技术指南中的 A 级绩效分级要求。
把 3 月 24 日一份更早的生态环境部门环评批复并排读,可以理解第三层如何落成设备动作(该批复为较早公开资料,此处仅引用工艺条款):电解车间配密闭高位分区集气与双烟管排烟,残极冷却烟气经封闭高效收集系统收集后进入「两段相向流干法烟气净化 + 石灰石—石膏法脱硫」;阳极组装车间各产尘点以封闭式集气罩收集、脉冲袋式除尘器处理;氧化铝与载氟氧化铝输送上料采用超浓相输送系统;严格控制开槽操作时间并在开槽时加大负压,换极操作时副烟管自动开启以增加槽膛负压;残极在厂内采用密闭拖车运输。A 级限值给出颗粒物 10、二氧化硫 35、氟化物 1.0 毫克/立方米。这些条款把「无组织」翻译成了可检查的密闭性、负压值与联锁动作。
三、为什么新鲜氧化铝仓与载氟氧化铝仓必须并列
干法脱氟以新鲜氧化铝作吸附剂,吸附电解烟气中的氟化氢后成为载氟氧化铝,再返回电解槽作为含氟原料使用,氟在厂内形成循环。因此两个仓的废气都不是普通粉料仓扬尘:前者是吸附剂入口,后者是吸附产物的中间贮运,两者都带氟、都必须纳入净化系统,且输送必须密闭。由此再看 11 月 9 日公示把「超浓相输送系统及废气收集系统」与「覆盖料输送系统」并列,就不是重复列项,而是两条粉尘特性不同的物料路径——气力输送的细粉料与覆盖在阳极上的粒状覆盖料,收集方式、风量与滤料选择都应分开设计。这一点也解释了覆盖料输送为何单独配 6 套集尘与 6 套布袋:点位分散、输送距离长,集中收尘的风量损失与管道积灰都难以接受。
四、「1 用 1 备」不是冗余,是连续性约束
脱硫塔 2 台 1 用 1 备、100 m 烟囱 2 根排气筒 1 用 1 备、抬包清理 2 套布袋 1 用 1 备,三处同时出现备机,指向同一条工程逻辑。抬包清理与残极冷却都是间歇性、阵发性的高浓度排放:换极、出铝、清理按班次发生,但净化系统不能随作业停启;备用配置保证单点检修时全线不停,也让阵发峰值有切换余量。与之相对,2 套干法脱氟对应的是电解烟气的连续负荷,不能按间歇逻辑配置。对设备维护的实际含义是:备用单元的可用率必须与主用单元同等考核,滤袋、脉冲阀、引风机与切换阀的状态要一并纳入点巡检,否则「1 用 1 备」只是纸面冗余。
五、返回料的验收:从「清理干净」到「不带入杂质」
11 月 10 日公示的固废条款给出一条关键边界:残极经残极处理系统处理后作为生产原料利用;而电解槽大修渣、碳渣、废机油等按危险废物分类暂存并交由有资质单位处置,脱硫石膏另行走综合利用。残极是可回用物料,碳渣与大修渣是危废——分类一旦明确,残极清理的验收标准就不只是表面干净,而是不能把电解质、磷铁环碎屑与钢爪氧化皮带进返回料,否则污染会随配料回到生阳极、再回到电解槽。
6 月一份行业协会分会的公开调研报道(发布于 6 月 21 日,调研发生于 6 月 5 日,属较早公开资料,此处仅引用工序与工艺参数)给出可对照的车间级参数:残极冷却破碎回收颗粒 ≤ 8 厘米、氟化物排放浓度控制在 3 mg/m³ 以下、残极需经电解质清理、抛丸、压脱等 10 余道工序后完成新阳极组浇铸、全程自动化率超 90%、生产线配备悬挂输送机与磷铁环压脱机等 24 种主体设备、磷生铁铁水温度 1350~1450 ℃、组装工序 23 类设备与 17 台工艺车辆纳入二维码点巡检、中频炉配炉体热成像与视频监控、输送皮带跑偏与撕裂异常可在线捕捉。工序数量与集气点数量是同步增长的:每多一道破碎、抛丸、压脱、清理,就多一个需要单独密闭与收尘的点位。11 月公示里那些按点位编号的集气罩与排气筒,正是这条十余道工序产线在环保侧的镜像。
六、落到车间:四条可核查的技术条目
- 集气与负压有读数。逐点检查集气罩密闭性、罩板与导杆间缝隙密封、管道负压测点;把开槽加大负压、换极副烟管自动开启这两类联锁动作纳入日常记录,让「无组织」变成有数值、有时序的参数,而不是验收时的一句定性描述。
- 点位与排气筒一一对应。沿用 6 套集尘 / 6 套布袋 / 6 根排气筒的编号化思路,建立「工序—集气罩—除尘器—排气筒」对照表;滤袋破损、风量衰减、脉冲阀失效都能定位到单一工位,避免全线排查。
- 返回料按粒度与夹带验收。以破碎粒度(如 ≤ 8 厘米)和电解质、铁质夹带作为清理质量的可测指标,而不是只看外观;这直接影响生阳极配料稳定性与残极回用比例,也决定后续粉尘点位的负荷。
- 易损件按点位归类备货。布袋与滤袋、脉冲阀、集气罩密封件、斗式提升机与螺旋输送部件、抛丸钢丸循环与分离装置、收尘风机与切换阀,是分段治理架构里决定实际收集效率的一类消耗件。按功能族建立清单与更换周期即可,无需涉及任何供货方或品牌信息。
七、一点判断
9 月 17 日一份行业研究报告把「电解烟气的深度净化治理技术全面升级」「全流程超低排放净化体系」列为工艺迭代的一部分,并指出技术进步已覆盖氧化铝生产、电解冶炼、烟气净化与智能控制的全流程;10 月 21 日公开的一场铝业周辅料市场研讨会报道中,有报告提出对预焙阳极炭块构建覆盖不同品级的四级评价体系、以统计学方法建立稳定性评价模型,把质量管控从「事后检验」推向「事前预防」,并提到阳极碳耗下降与换极周期延长。把这两条与 11 月的设备清单放在一起看,可以给出一个判断:阳极侧的技术竞争正从单件质量,扩展到「质量 + 返回料洁净度 + 排放点位可控性」三者的组合。对存量产线而言,改造难点往往不在新增一台净化设备,而在把已有的十余道工序按点位重新编号、补齐密闭与收尘、让每个点位都有可测的风量与可追溯的维护记录。本文为公开资料整理与独立观察,不同项目、不同年度口径不合并,与本公司业务、客户或业绩无关。
The three earlier technical notes in this column looked at the origins of the iron-carbon voltage drop (8 November), the cast-iron slag-cleaning station and molten-metal temperature and composition (11 November), and the reuse chain for anode rod assemblies and steel claws (14 November). This one shifts the camera to the other side of the line: the fumes, dust and return material left behind in the anode assembly shop after spent anodes and electrolyte leave the cell. On 9 and 10 November 2026, two EIA documents published by ecology and environment authorities broke this chain - usually written off as ancillary works - into a countable schedule of capture points. Every figure and technical clause below is labelled with its source and the year it applies to; figures from different projects are not merged. This note is a compilation of public information and independent commentary, not investment, procurement or engineering advice, and is unrelated to our company's business, clients or track record.
1. Two November disclosures: the spent-anode side becomes countable
A first-round public-participation EIA notice for an aluminium smelter capacity-swap project, posted on a county government website on 9 November, states its construction scope directly: 64 new 600 kA prebaked-anode cells with corresponding dense-phase conveying and gas-collection systems, 8 spent-anode fume capture units, 2 covering-material conveying systems and 1 aluminium-dross treatment system. The project is explicitly a capacity swap and adds no new smelting capacity. What matters is that the spent-anode fume capture units are counted separately - 8 of them - and listed alongside, not inside, the cells' own gas-collection system. In a large prebaked-cell configuration, spent-anode cooling fumes are no longer an appendage handled together with cell gas; they are a process unit with dedicated equipment and its own count.
A draft EIA approval disclosure issued by a provincial ecology and environment authority on 10 November breaks operational air emissions down further: cell and spent-anode cooling fumes, covering-material conveying exhaust, fresh-alumina and fluorinated-alumina silo exhaust, bucket-elevator exhaust, holding-furnace exhaust after retrofit, and crucible-cleaning exhaust after relocation. Seven classes of point, each with its own treatment train - effectively an emission inventory numbered by process step.
2. A three-layer control architecture
| Point (10 November disclosure) | Treatment equipment | Discharge route |
|---|---|---|
| Fresh- and fluorinated-alumina silos, cell gas; particulate matter, fluorides, sulphur dioxide | 2 dry defluorination systems + 1 wet desulphurisation system (2 towers, 1 duty / 1 standby) | 100 m stack (2 ducts, 1 duty / 1 standby) |
| Covering-material conveying exhaust | 6 dust-collection sets + 6 bag filters | Six 15 m stacks |
| Bucket-elevator conveying exhaust | 2 bag filters | Two 15 m stacks |
| Holding-furnace exhaust | 1 bag filter | One 15 m stack |
| Crucible-cleaning exhaust | 2 bag filters (1 duty / 1 standby) | One 20 m stack (1 duty / 1 standby) |
Three layers emerge. The first handles gaseous pollutants and fine particulates by adsorption and absorption, serving the continuous, high-volume cell gas stream. The second handles mechanical dust from material transfer and cleaning, using local hoods, bag filters and short stacks, serving dispersed, intermittent point sources. The third handles fugitive emissions that never reach a stack at all, controlled by containment, negative pressure and operating procedures. The disclosure requires every stack to meet the special atmospheric emission limits of the Aluminium Industry Pollutant Discharge Standard (GB 25465-2010, as amended) and the Grade-A performance grading requirements in the technical guideline for emergency emission reductions in key industries during heavy-pollution weather.
An earlier approval published on 24 March by an ecology and environment authority shows how the third layer becomes concrete equipment actions (this is an older public document; only its process clauses are cited here). The cell room uses sealed high-level zoned capture and twin-duct extraction; spent-anode cooling fumes are collected by a closed high-efficiency system and treated by two-stage counter-current dry gas purification plus limestone-gypsum desulphurisation. Dust points in the anode assembly shop are captured by closed hoods and treated by pulse-jet bag filters. Alumina and fluorinated alumina are conveyed and charged by dense-phase systems. Slot-opening time is strictly limited and negative pressure is increased during slot opening; the auxiliary duct opens automatically during anode changes to raise cell-cavity negative pressure. Spent anodes move inside the plant in sealed trailers. The Grade-A limits are 10 mg per cubic metre for particulate matter, 35 for sulphur dioxide and 1.0 for fluorides. In other words, fugitive emissions are translated into checkable containment integrity, pressure readings and interlock actions.
3. Why fresh-alumina and fluorinated-alumina silos must both sit inside the loop
Dry defluorination uses fresh alumina as the adsorbent. After capturing hydrogen fluoride from cell gas it becomes fluorinated alumina, which returns to the cells as a fluorine-bearing feed, closing a fluorine loop inside the plant. Neither silo therefore behaves like an ordinary powder store: one is the adsorbent inlet, the other is intermediate storage of the adsorption product. Both carry fluorine, both must be included in the purification system, and both must be conveyed in sealed dense-phase lines. This also explains why the 9 November notice lists a dense-phase conveying and gas-collection system separately from the covering-material conveying system. These are two material paths with different dust behaviour - pneumatically conveyed fine powder versus granular covering material placed on the anodes - and their capture method, air volume and filter media should be designed separately. It also explains the 6 dust-collection sets and 6 bag filters for covering-material conveying: the points are dispersed and the conveying runs are long, so a single central collector would lose air volume and accumulate dust in the ducts.
4. Duty / standby is a continuity constraint, not spare capacity
Two desulphurisation towers with one on standby, two 100 m stack ducts with one on standby, and two bag filters for crucible cleaning with one on standby all appear in the same document, and they point to one engineering logic. Crucible cleaning and spent-anode cooling are intermittent, pulsed, high-concentration sources: anode changes, metal tapping and cleaning happen by shift, but the purification system cannot start and stop with them. The standby unit keeps the line running during maintenance at a single point and gives headroom for pulsed peaks. By contrast, the 2 dry defluorination systems serve the continuous load of cell gas and cannot be sized on an intermittent logic. For maintenance the implication is concrete: the standby unit must be held to the same availability standard as the duty unit, and filter bags, pulse valves, induced-draught fans and changeover valves must all be inside the inspection round. Otherwise duty / standby is redundancy on paper only.
5. Acceptance criteria for return material: from clean-looking to contamination-free
The solid-waste section of the 10 November disclosure draws a decisive boundary: spent anodes, after passing through the spent-anode treatment system, are used as production feed, whereas spent potlining, carbon slag and waste oils are stored separately as hazardous waste and handed to qualified disposal operators; desulphurisation gypsum goes to separate comprehensive utilisation. Spent anodes are a reusable material; carbon slag and potlining are hazardous waste. Once that classification is fixed, the acceptance test for anode cleaning can no longer be a visual judgement of cleanliness. The requirement becomes that electrolyte, cast-iron ring fragments and steel-claw oxide scale must not be carried into the return material - otherwise contamination travels back into green anode formulation and from there back into the cell.
A workshop report published by an industry association branch in June (issued 21 June, describing a 5 June visit; an older public source, cited here only for process steps and parameters) gives comparable shop-floor figures: crushed spent anodes recovered at a particle size of 8 cm or below, fluoride emissions held below 3 mg per cubic metre, more than ten steps including electrolyte removal, shot blasting and pressing-off before a new anode assembly is cast, automation above 90 percent across the line, 24 main equipment types including overhead conveyors and cast-iron ring press-off machines, molten cast iron at 1350-1450 degrees Celsius, 23 equipment classes and 17 process vehicles under QR-code-based inspection rounds, thermal imaging and video monitoring on the medium-frequency furnace, and online detection of belt mistracking and tearing. Process steps and capture points grow together: every added crushing, blasting, pressing-off or cleaning step creates one more point that must be sealed and extracted on its own. The numbered hoods and stacks in the November disclosures are the environmental mirror of that ten-plus-step line.
6. Four auditable items for the shop floor
- Give capture and negative pressure a reading.Check hood tightness, sealing of gaps between cover plates and anode rods, and duct pressure taps point by point; log the two interlock actions - increased negative pressure during slot opening and automatic auxiliary-duct opening during anode changes - so that fugitive emissions become a measured, time-stamped parameter rather than a qualitative line at acceptance.
- Map one point to one stack.Follow the numbering logic of 6 collection sets / 6 bag filters / 6 stacks and build a step-to-hood-to-filter-to-stack register. Bag damage, air-volume decay and pulse-valve failure can then be located at a single station instead of triggering a line-wide search.
- Accept return material by particle size and entrainment.Use crushed particle size (for example, 8 cm or below) and electrolyte or iron entrainment as measurable quality indicators instead of appearance. These directly affect green-anode formulation stability and the spent-anode recycle ratio, and they set the load on every downstream dust point.
- Stock wear parts by point and by function.Filter bags, pulse valves, hood seals, bucket-elevator and screw-conveyor components, shot-blasting media circulation and separation units, extraction fans and changeover valves are the consumables that determine real capture efficiency in a segmented architecture. A functional parts list with replacement intervals is sufficient; no supplier or brand information is needed.
7. One judgement
An industry research report dated 17 September lists the comprehensive upgrade of cell-gas deep purification and full-process ultra-low-emission systems as part of the sector's process iteration, and argues that technical progress now spans alumina production, smelting, gas cleaning and intelligent control. A report from an aluminium-week auxiliary-materials seminar published on 21 October proposes a four-tier evaluation system for prebaked anode blocks across quality grades, with statistical stability models that move quality control from post-hoc inspection to prevention, and reports lower anode carbon consumption and longer anode-change cycles. Read alongside the November equipment schedules, these suggest that competition on the anode side is expanding from single-piece quality to a combination of quality, cleanliness of return material, and controllability of emission points. For an existing line, the hard part of a retrofit is rarely buying one more purifier. It is re-numbering a dozen existing steps point by point, closing and extracting each one, and giving every point a measured air volume and a traceable maintenance record. This note is a compilation of public information and independent commentary; figures from different projects and years are not combined, and it is unrelated to our company's business, clients or track record.